Home automation in a renovation: KNX, Zigbee and smart home
Automating a home is no longer the stuff of science fiction, or a luxury reserved for mansions in Silicon Valley. Today, building smart technology into a deep renovation is simply a sound decision for design, efficiency and resale value. When you open up walls and rethink the services, you get a chance that will not come round again for decades.
But the market is full of jargon, acronyms and sales promises that often confuse more than they help. Should you go for the industrial-grade robustness of KNX wiring, or is the quick, low-cost flexibility of Zigbee wireless devices and the newer Matter standard enough? In this guide we answer your questions so you can make the right technical choice without fear of getting it wrong.
Key points to know:
- Right moment: Planning the installation together with the full home renovation avoids cosmetic patches and later extra costs.
- Mixed solutions: You do not have to choose one route. Modern gateways let you build stable hybrid systems.
- Site strategy: Knowing how to organise a full renovation step by step will make sure the electricians and home automation installers work in step with each other.
- Property value: Well-done home automation pre-wiring adds real appeal when you sell a flat in the main cities.
The best opportunity: why automate during a full renovation?
If you have ever tried fitting smart bulbs or motion sensors in an older, occupied home, you will know how frustrating it is to deal with too few sockets, Wi-Fi dead spots and ugly adapters sticking out of the walls. The key to a successful tech project is not the final device but the infrastructure behind it that supports it and powers it. When you knock down partitions, replace false ceilings and lift old floors, that infrastructure becomes easy to reach all at once.
So instead of worrying about hiding cables afterwards, you can plan a clean network of generously sized corrugated conduit that runs from every key point in the home straight back to the main consumer unit. This not only saves you cosmetic headaches, it also cuts labour costs considerably. An electrician working on bare walls can run conduit through a whole home in a fraction of the time it would take in a painted, finished space.
And it is not only about lights or blinds. Modern thermal comfort depends heavily on precise control. If you are upgrading heavy climate-control systems, controlling the temperature from discreet smart sensors in each room will completely change how everyone in the house experiences heating and cooling. But to make all this silicon and copper machinery work without friction, we need to look at the two main highways that carry information around the home.
KNX: the wired backbone of professional automation
When it comes to high-end luxury renovations, the flagship system is still KNX. It is the only open global standard for controlling smart homes and buildings, governed by a strict protocol developed over more than three decades. It works by physically separating electrical power from the transmission of digital signals.
What does that mean in practice? Your switches, presence sensors, thermostats and blind motors all connect to each other through a single green cable: a twisted-pair communication bus that carries low voltage, so commands are sent safely. At the other end of this cable, in the main control and protection board, sit dedicated actuators that switch the traditional 230-volt mains supply to the points of use in the home.
The big advantage of this decentralised design is its complete safety and immunity to radio interference or congested Wi-Fi networks in dense urban areas. If the central processor of a generic home automation server fails in a conventional installation, the whole house goes blind and deaf. In a pure KNX system, each connected device has its own self-managed local intelligence. So if a room sensor were to fall off the wall, the rest of the home would carry on running as normal.
Zigbee and Matter: flexibility and the new wireless order
On the other side of the technical balance are wireless solutions, traditionally led by the Zigbee protocol. Unlike Wi-Fi, which loads your home router with heavy traffic and uses a fair amount of power, Zigbee builds a self-healing mesh network.
In this mesh, every device that is permanently mains-powered (such as a smart wall switch, a smart plug or a DIN-rail module) also acts as a signal repeater. That lets the network grow organically and route signals around obstacles such as thick concrete load-bearing walls or heavy floor slabs. The standby power draw of Zigbee end devices is so low that battery-powered sensors, such as flood sensors or window contacts, can run for several years before they need a new battery.
On top of that, Matter is now becoming firmly established. This new universal interoperability standard, backed jointly by the largest companies in the industry, promises solid software bridges between brands. The big advantage for the owner is that you no longer need to worry whether an automation device works with Apple, Google or Amazon. However, to avoid the common renovation mistakes, it is essential to plan a practical way for the systems to coexist, so that software does not compromise the basic electrical reliability of the home.
Detailed technical comparison
To simplify your decision before the hammering starts on site, we have prepared this comparison table of the key factors that will shape how your home behaves day to day, in the medium and long term:
| Key parameter | Wired KNX system | Wireless Zigbee / Matter |
|---|---|---|
| Transmission route | Dedicated twisted copper bus (immune to interference). | Meshed radio waves (2.4 GHz). |
| Installation requirements | Chases, dedicated conduit and large back boxes. | Minimal. The modules fit behind existing switches. |
| Total upfront cost | High (requires a certified installer and licensed software). | Affordable, scalable and with a very low entry cost. |
| Local reliability | Almost 100% maintenance-free over decades. | Medium to high. Depends on the stability of the nodes. |
| Long-term support | Certified devices from different brands that work with each other. | Depends on software updates from third-party makers. |
| Installer profile | Home automation systems integrator certified as a KNX Partner. | Can be installed by you or by an up-to-date electrician. |
The invisible core: consumer unit and low-voltage rules in automation work
Any serious change to a home's wiring must comply with the Low-Voltage Electrotechnical Regulations (REBT). When you plan a deep automation project, this legal side becomes crucial because of the large number of devices that end up in the consumer unit. If you are upgrading the electrical installation in the home, be prepared to set aside a considerably larger space than usual inside your built-in cupboard.
But size is not the only regulatory factor. For the 230V single-phase power lines and the very-low-voltage safety lines that carry data on KNX's green bus (30V DC) to coexist safely, the conduit must run completely separately. The two may only meet inside back boxes specifically designed with fire-resistant internal dividers.
So if you plan to fit modern switches that bring all the controls of a room together in one sleek push-button panel, make sure your installer lays out the electrical circuits logically. The main control board must be physically oversized in width and in the number of free DIN rails, so the modules can shed their residual heat. It also has to be built from the start to pass the official technical inspection without any regulatory problems.
The climate of the future: integrating heat pumps and underfloor heating
In terms of savings and comfort, one of the happiest engineering pairings is renewable efficiency combined with zone-by-zone smart control. Today, integrated aerothermal heating and climate control is the clear choice of energy-conscious households, thanks to its impressive heat output for every unit of electricity used.
But to get the most out of that heat, controlling water-based underfloor heating through physical automation gateways becomes essential. Unlike a conventional metal radiator, a heating system with underfloor pipes has very high thermal inertia. The floor takes several hours to warm up after the central valve opens, and the same time again to give up its residual heat once it is switched off.
This is where a smart controller really makes the difference. By putting humidity and temperature sensors in the rooms and connecting them to self-learning algorithms, the aerothermal heat pump runs at a low flow temperature only during the hours when electricity tariffs are cheapest. The system can also predictively adjust motorised blinds to let in free passive solar heat through the windows, while protecting the rooms from excess sun during the hottest hours of summer.
Hybrid design strategies for characterful older buildings
Not every home project starts with the blank canvas of a new-build or a new single-family house. When renovating an older flat in Barcelona's Eixample, for example, technicians often find traditional ceramic-block floor slabs, protected Baroque ceiling mouldings and thick solid masonry walls. These stop pipes, or stable radio signals, from passing through cleanly.
To overcome this physical barrier, the best approach is a hybrid design. One good option is to hire an experienced renovation company or self-employed renovator who understands that the core fixed infrastructure (main lighting built into false ceilings and centralised climate control) should be wired on a physical data bus. The secondary accessories, such as cabinet sensors, auxiliary table lamps or portable switches, can then run on local Zigbee mesh networks.
This way you keep the basic electrical installation fully robust against any software failure or network change. You avoid both the prohibitive cost and the irreparable damage to the building that would come from running copper bus cabling to every corner of a historic property.
Recommended technical guides for your project:
Before buying smart equipment or signing a works contract in Catalonia, to make sure the project is financially viable, we strongly recommend reviewing the following information on our site:
- Read our full guide to how much it costs to renovate a flat, based on current market rates.
Frequently asked questions (FAQ)
What is the main difference between KNX and Zigbee when renovating?
The key difference is the transport infrastructure. KNX uses a dedicated physical cable bus, which gives it rock-solid stability at the cost of chasing walls and running conduit during the works. Zigbee works over radio frequency through a wireless mesh network, offering a quicker and less invasive installation.
Is KNX compatible with new wireless devices that use Matter?
Yes, it is fully compatible, thanks to dedicated IP-Matter gateways that act as translators. This means a robust wired system can control newer wireless devices as one coherent system, all from a single native app on your phone.
Do I need to allow extra space in my consumer unit?
Definitely. A professional-level centralised home automation installation needs large distribution cabinets to house actuators, power supplies and communication gateways. That goes beyond the size of a standard consumer unit.
Can I combine a heat pump and underfloor heating with home automation?
Yes, and it is currently the most efficient combination. Managing the underfloor heating, which has high thermal inertia, together with the heat pump optimises the on and off cycles based on indoor and outdoor temperature curves.
Summing it up
Automating your home during building work is the only realistic way to get a house that truly responds to your habits and needs. Do not leave these crucial points until the early stage of the floor plans. Talking openly with your architects and home automation integrators from the first few weeks will save you thousands of euros and give you a home that is far more comfortable, durable and adaptable.
Keep reading
What is the REBT? The low-voltage electrotechnical regulation
What the REBT is, Spain's low-voltage electrical regulation, its technical instructions (ITC-BT) and the key changes that affect homes in 2026.
InstallationsWhat is the ICP (power control switch)?
What the ICP power control switch is, how the old physical device became a digital meter limit, and how it affects your renovation work in 2026.
InstallationsWhat is underfloor heating?
What underfloor heating is, how it works, water versus electric systems, the cost per m², the trade-offs and how to fit it in a renovation.

